TOPOLOGI ROUTING OSPF 1 dan RIP VERSION 2
KONFIGURASI ROUTER 0
langkah 1.
Router#conf ter
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int gig0/0
Router(config-if)#no sh
Router(config-if)#no shutdown
Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up
Router(config-if)#ex
Router(config)#int gig0/1
Router(config-if)#no sh
Router(config-if)#no shutdown
Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up
Router(config-if)#ex
Router(config)#int gig0/2
Router(config-if)#no sh
Router(config-if)#no shutdown
Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/2, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/2, changed state to up
langkah 2.
Router(config-if)#ex
Router(config)#int gig0/1
Router(config-if)#ip add 40.40.40.1 255.255.255.0
Router(config-if)#no sh
Router(config-if)#ex
Router(config)#int gig0/0
Router(config-if)#ip add 10.10.10.1 255.255.255.0
Router(config-if)#no sh
Router(config-if)#ex
Router(config)#int gig0/2
Router(config-if)#ip add 192.168.1.1 255.255.255.0
Router(config-if)#no sh
Router(config-if)#ex
Router(config)#do wr
Building configuration...
[OK]
Router(config)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to up
langkah 3.
Router(config)#router rip
Router(config-router)#version 2
Router(config-router)#ne
Router(config-router)#network 10.10.10.0
Router(config-router)#network 40.40.40.0
Router(config-router)#network 192.168.1.0
Router(config-router)#do wr
Building configuration...
[OK]
Router(config-router)#ex
Router(config)#
CONFIG ROUTER 1
langkah 1
Router#conf ter
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int gig0/0
Router(config-if)#no sh
Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up
Router(config-if)#ex
Router(config)#int gig0/1
Router(config-if)#no sh
Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up
langkah 2
Router(config-if)#ex
Router(config)#int gig0/0
Router(config-if)#ip add 10.10.10.2 255.255.255.0
Router(config-if)#no sh
Router(config-if)#ex
Router(config)#int gig0/1
Router(config-if)#ip add 20.20.20.1 255.255.255.0
Router(config-if)#no sh
Router(config-if)#ex
Router(config)#do wr
langkah 3
Router(config)#router rip
Router(config-router)#ver
Router(config-router)#version 2
Router(config-router)#network 10.10.10.0
Router(config-router)#ex
Router(config)#router ospf 1
Router(config-router)#network 20.20.20.0 0.0.0.255 area 0
Router(config-router)#do wr
Building configuration...
[OK]
Router(config-router)#ex
Router(config)#
00:18:06: %OSPF-5-ADJCHG: Process 1, Nbr 192.168.2.1 on GigabitEthernet0/1 from LOADING to FULL, Loading Done
Router(config)#router rip
Router(config-router)#ver
Router(config-router)#version 2
Router(config-router)#red
Router(config-router)#redistribute ospf 1 metric 1
Router(config-router)#ex
Router(config)#router ospf 1
Router(config-router)#red
Router(config-router)#redistribute r
Router(config-router)#redistribute rip s
Router(config-router)#redistribute rip subnets
Router(config-router)#do wr
Building configuration...
[OK]
Router(config-router)#ex
Router(config)#
KONFIGURASI ROUTER 2
Router>en
Router#conf ter
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int gig0/0
Router(config-if)#no sh
Router(config-if)#no shutdown
Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up
Router(config-if)#ex
Router(config)#int gig0/1
Router(config-if)#no sh
Router(config-if)#no shutdown
Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up
Router(config-if)#ex
Router(config)#int gig0/0
Router(config-if)#ip add 40.40.40.2 255.255.255.0
Router(config-if)#no sh
Router(config-if)#ex
Router(config)#int gig0/1
Router(config-if)#ip add 30.30.30.1 255.255.255.0
Router(config-if)#no sh
Router(config-if)#no shutdown
Router(config-if)#ex
Router(config)#do wr
Building configuration...
[OK]
Router(config)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to up
Router(config)#router rip
Router(config-router)#ver
Router(config-router)#version 2
Router(config-router)#net
Router(config-router)#network 40.40.40.0
Router(config-router)#do wr
Building configuration...
[OK]
Router(config-router)#ex
Router(config)#router ospf 1
Router(config-router)#net
Router(config-router)#network 30.30.30.0 0.0.0.255 area 0
Router(config-router)#do wr
Building configuration...
[OK]
Router(config-router)#e
00:19:23: %OSPF-5-ADJCHG: Process 1, Nbr 192.168.2.1 on GigabitEthernet0/1 from LOADING to FULL, Loading Done
x
Router(config)#router rip
Router(config-router)#ver
Router(config-router)#version 2
Router(config-router)#red
Router(config-router)#redistribute o
Router(config-router)#redistribute ospf 1 m
Router(config-router)#redistribute ospf 1 metric 1
Router(config-router)#ex
Router(config)#do wr
Building configuration...
[OK]
Router(config)#router ospf 1
Router(config-router)#red
Router(config-router)#redistribute rip s
Router(config-router)#redistribute rip subnets
Router(config-router)#do wr
Building configuration...
[OK]
Router(config-router)#ex
Router(config)#
CONFIGURASI ROUTER 3
Router>en
Router#conf ter
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int gig0/0
Router(config-if)#no sh
Router(config-if)#no shutdown
Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up
Router(config-if)#ex
Router(config)#int gig0/1
Router(config-if)#no sh
Router(config-if)#no shutdown
Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to up
Router(config-if)#ex
Router(config)#int gig0/1
Router(config-if)#ip add 20.20.20.2 255.255.255.0
Router(config-if)#no sh
Router(config-if)#no shutdown
Router(config-if)#ex
Router(config)#int gig0/0
Router(config-if)#ip add 30.30.30.2 255.255.255.0
Router(config-if)#no sh
Router(config-if)#ex
Router(config)#int gig0/2
Router(config-if)#no sh
Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/2, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/2, changed state to up
Router(config-if)#ex
Router(config)#int gig0/2
Router(config-if)#ip add 192.168.2.1 255.255.255.0
Router(config-if)#no sh
Router(config-if)#no shutdown
Router(config-if)#ex
Router(config)#do wr
Building configuration...
[OK]
Router(config)#router ospf 1
Router(config-router)#net
Router(config-router)#network 20.20.20.0 0.0.0.255 area 0
Router(config-router)#network 30.30.30.0 0.0.0.255 area 0
Router(config-router)#network 192.168.2.0 0.0.0.255 area 0
Router(config-router)#do wr
Building configuration...
[OK]
Router(config-router)#ex
Router(config)#
0 komentar:
Posting Komentar